Cardinal Health Aluminum Lightweight Transport Chair
Cardinal Health Aluminum Lightweight Transport Chair

Cardinal Health Aluminum Lightweight Transport Chair

Brand/Manufacturer: CARDINAL HEALTH
Save
Authorized Retailer Badge
  • FSA Approved

Cardinal Health Aluminum Lightweight Transport Chair is designed for quick and easy patient transport without cumbersome bulkiness of a wheelchair. It features quick release fold-down back and removable swing-away leg riggings. Also features padded fixed armrests, dual push-to-lock rear wheel brakes, adjustable seat belt and powder-coated finish frame. Not made with natural rubber latex.

Cardinal Health Aluminum Lightweight Transport Chair is Discontinued by Manufacturer. You may look for the replacement. Click here for Invacare ProBasics Steel Transport Wheelchair With Swing Away Footrest

Features

  • Invacare Manual Wheelchair has elevating and adjustable leg rests which include calf pads for added comfort
  • Fixed full-length arms for arm support along the entire depth of the seat
  • Vinyl arm pads provide cushioned support
  • Foot plates are height adjustable for a customized fit
  • Folds easily for convenient storage and transport
  • 8-inch mag-style and dual-locking rear wheels
  • Durable nylon padded upholstery seat is easy to clean
  • Steel construction with chrome or charcoal finish
  • Includes tool kit for minor repairs and replacement parts
  • Easy to assemble – tool kit included
  • Not Made with Natural Rubber Latex

More Information

Adjusting Transport Chair -

  • To Open Chair: Open chair by tilting to one side and pushing down on seat rail.
  • To Close/Fold Chair: To fold chair pull up locks and carefully fold down the back support. Place foot plates in a vertical position. Grab seat with both hands at front and back edges. Then lift or tilt chair to one side and lift up seat rail.
  • Adjusting Height of Foot Plates: Sit in chair with your feet on the foot plates. Loosen the bolt found on clamp around support assembly. Raise or lower foot plate to a position that provides the most support of your thighs. Front rigging should not be so low that it causes uncomfortable pressure to thighs at front of seat upholstery. Foot plates should not be lower than 2½ inches from the ground to ensure proper clearance.
  • Elevating/Lowering Leg Rests: Sit in chair with your feet on the foot plates. Hold the leg rest support tube to raise the leg rest until the desired position is reached. To lower the leg rest. Support the leg rest with one hand while pushing the release lever then slowly lower the leg rest to the desired position.
  • Removal of Leg or Foot Rests: Release lock by pushing on the front rigging lever. Swing leg or foot rest out and sideways then lift to remove.
  • Wheel Locks: Engage both wheel locks before getting in or out of chair, leaning forward in chair or while in an elevator or wheelchair lift. Locks are engaged by pushing handles completely forward. Adjustments to locks are made by loosening or tightening nut on the carriage bolt. Embed lock shoe at least 1/8 inch by sliding clamp toward rear wheel while handle is engaged in locked position. Tighten nut and bolt to secure in position. Test for correct locking action before actual use.

General Care -

  • Frame/Hand Grips: Wipe metal parts with a soft cloth at least once a week. All metal parts can be cleaned with auto wax or similar products. If exposed to moisture dry immediately. Do not use an abrasive cleanser that will scratch the finish. Use only a clean towel dampened with cool water when cleaning hand grips. Confirm that the grips are dry before using. NEVER use ammonia-based cleaning solutions or soap on hand grips, which may cause them to loosen or crack.
  • Wheels: Wheels should be inspected at least once a month to ensure proper tightness. If wheel wobbles or loose, release lock nut and tighten axle bolt slightly. Test for proper tightness and alignment by leaning chair to one side and spinning adjusted wheel.
  • Tires: Tires need minimal maintenance and should be cleaned as needed with a damp cloth. Replace if tires become worn or cracks appear.
  • Front Casters: Check casters and lubricate as needed. Lubricate by removing fork and greasing caster stem bearings with high-quality multi-purpose grease. Lubricate wheel bearings by removing wheel from fork. Reassemble fork and wheel by tightening nuts until no play remains, but wheels roll freely. If nuts are too loose, caster will shimmy and if it is too tight chair will be difficult to steer.

Specification

Dimensions

Size

Weight capacity

300 lbs

Overall height

39.5"

Overall width (Open)

22.25"

Overall width (Closed)

9.25"

Seat width

19"

Seat depth

16"

Seat to floor height

19.25"

Seat back height

19"

Warranty

1 year warranty

Customer Reviews

Questions & Answers


 
 
question image
My father is 6.5 will this wheelchair fit his length? 
Patricia Bailey - 8/21/2017 5:07:15 PM
facebooktwitter
answer image
As the vendor the dimensions of the chair is: 
  • Seat to floor height: 19-1/4". 
  • Overall height: 39-1/2"
  • Overall width: 22-1/4" open; 9-1/4" closed 
  • Seat width: 19"
  • Seat depth: 16"
  • Seat back height: 19"
  • 8" low-maintenance castor wheels
  • Weighs just 20-1/4 lbs without footrests with a 300-lb weight capacity
Customer care - 8/29/2017 7:17:14 AM
answer image
Dear Sir/Madam, thanks for your inquiry. We'll try to get back to you shortly regarding this.
Customer care - 8/23/2017 7:59:28 AM
question image
Weight
Leah - 7/30/2016 9:36:47 AM
facebooktwitter
answer image
Thank you for reaching out to us. The weight is 41 lbs.
Customer Care - 8/1/2016 7:05:41 AM
Please enter your and your friends email address below.
Fields marked with * are compulsory
 
*
*
*
*

 
SubmitCancel
The selected product information has been successfully emailed to your friend.

Thank you for using www.shopwheelchair.com

Close